DG100 is compact and efficient Multi-service IoT Edge Gateway for home, office and industrial applications.
DL28 is a communications processor that handles data communication connections between measuring and control devices in a heating substation and their integration into remote monitoring and control systems (SCADA) by using diverse transfer routes.
DMS100 series is RS485 Modbus sensor with unlimited application potential. Due to its simplicity, the Modbus protocol is a widely used method of communication for sensing and automation.
DWS100 series of wireless sensors have unlimited application potential. They are used for environmental monitoring, agriculture, smart buildings, health care and so on.
DSH101 sensor hub devices are radio access point and interface between multiple DWS100 wireless sensors and host devices. This family helps to acquire and integrate data from wireless sensor network based on SimplRF and communicate to host side.
IDM 50B is a frequency shift keyed (FSK) and quadrature amplitude modulation (QAM) modem for asynchronous and synchronous data transmission in 300-3400 Hz voice band. It is highly immune to interference and noise and permit extensive voice-band communication link utilization.
DECODE GT340 is compact dual-band GSM/GPRS terminal which enables easy connection of the user devices and PCs to the GSM network. It is based on uBlox SARA-G340 module with integrated TCP/IP stack. The micro SIM card is placed through the hole on the front panel of the device.
DECODE GT900 is compact quad-band GSM/GPRS terminal which enables easy connection of user devices and PCs on GSM network. It is based on Simcom SIM900 module with integrated TCP/IP stack.
RPBS-868 is device intended for wireless transfer of commands in unlicenced radio frequency range. It has four galvanically isolated digital inputs, four relay outputs and additional relay for indication of valid connection.
RRSW-868 is device intended for wireless transfer of commands in unlicensed radio frequency range. It has two galvanically isolated digital inputs, two relay outputs and additional relay for indication of valid connection.
PRM 4 is packet radio modem intended for wireless transfer of serial protocols in unlicensed ISM 868MHz frequency range. It has RS-232 DCE, as well as two wire or four wire RS-422 or RS-485 interface.
MM20 is interface converter intended for feeding and transparent reading of M-Bus slave devices. Converter has RS-232, RS-485 and Ethernet interfaces, where the lowest priority is dedicated to RS-232 and the highest to Ethernet interface.
MM20-USB is interface converter intended for transparent readout and power supply of M-Bus slave devices. Converter is powered from USB port and galvanically isolated from the M-Bus line. LED indications show power supply presence, data transmit and receive.
MM20-GSM is communication device intended for remote readout over GSM/GPRS connection:
– devices on M-Bus line with M-Bus protocol (heat, water, electric, gas meters…)
USB/422-485 ISO is a communication converter intended for connecting RS-422/485 devices to PC’s USB port. Data rate and format adjustment is performed according to requirements of RS-422/485 device. Module is power supplied from USB port and galvanic isolated from RS-422/485 devices (network).
232/422-485 is a communication converter intended for connecting serial industrial buses and devices with RS 422-485 connector to PC serial port. By connecting this module to PC, capacity of “high-speed” RS422-485 ports is additionally extended.
USB/232 ISO is a communication converter intended for interconnecting industrial serial buses and devices with RS-232 connection to PC’s USB port. Connecting this converter to PC additionally exceeds the capacity of RS-232 ports.
Repeater 422-485 is a communication converter intended to use for galvanic isolation, and range and capacity extension of RS422-485 network. Operating mode, line termination, baud rate and data format are easy selectable by DIP switches mounted inside of the device.
NetX Ethernet converter enables interconnection of serial RS-232/422/485 line and Ethernet network with transparent conversion of serial protocols in to UDP or TCP/IP packets. NetX provides conversion of physical and electrical interfaces, way of medium access and speeds between two communication networks.
Functionality of the following devices is available in three different platforms, 110, 343 and 686, with different hardware resources, shown in Table of hardware platforms. Analog inputs can be configured to work as voltage or current inputs.
DECODE EMU devices represent series of measuring devices for measurement of AC and DC voltages and currents with integrated RS-485 Modbus connection.There are three different device options supported where the third one…
SCM 311/312/313 is industrial measurement converter who has current signal 4-20mA as his output signal, equivalent to voltage of pH and ORP/conductivity/ DO input signal.Transducer has a galvanic input/output isolation, wide range power supply, high input impedance…
SCM 201 is a galvanic isolated transducer for 35mm DIN rail mounting that converts input – alternate current (0-5A AC), to 4-20mA current. Conversion is proportional and linear. Transducer is supplied from measurement loop since output connection (4/20mA current) is passive 2-wire.
SCM 202 is a galvanic isolated transducer for 35mm DIN rail mounting that converts input – alternate voltage (0-500V AC), to 4-20mA current. Conversion is proportional and linear. Transducer is supplied from measurement loop since output connection (4/20mA current) is passive 2-wire.
SCM 203 is a current isolator intended for mounting on DIN 35mm rail. It provides galvanic isolation of current sensing loops. Conversion is linear. Connecting of input (4-20mA) and output (4-20mA) current is two way and passive which means that converter is power supplied from current loops
Serial Cable Assembly 0.3m, RJ45 Male – DB9 Male
Ethernet patch cable, RJ45 Male – RJ45 Male
USB Cable Type A/B 1.8~2m
Power supply, DIN rail mount, DC24V 15W, AC85-264V 50/60Hz